Skip to article frontmatterSkip to article content
Site not loading correctly?

This may be due to an incorrect BASE_URL configuration. See the MyST Documentation for reference.

POD Analysis

Open from ‘3. Analysis →\to POD Analysis‘.

Proper Orthogonal Decomposition (POD) finds the most efficient low-dimensional representation of the velocity field by decomposing the fluctuation field into a set of orthogonal spatial modes ϕn(x)\boldsymbol{\phi}_n(\mathbf{x}) and corresponding temporal coefficients an(t)a_n(t):

u′(x,t)=∑n=1Nan(t) ϕn(x)\mathbf{u}'(\mathbf{x}, t) = \sum_{n=1}^{N} a_n(t)\,\boldsymbol{\phi}_n(\mathbf{x})

The modes are ordered by their energy content: Mode 1 captures the largest fraction of the total TKE, Mode 2 the next largest, and so on. This property, known as optimality, means that the POD is the most efficient basis for representing the flow in a least-squares sense (Lumley, 1967; Holmes et al., 1996). In practice, a small number of modes often captures the dominant coherent structures (recirculation zones, vortex shedding, shear layer flapping), while the remaining modes represent incoherent noise.

uPrime implements the snapshot POD method (Sirovich, 1987), which is efficient when the number of spatial grid points exceeds the number of snapshots. The SVD of the fluctuation snapshot matrix directly yields the POD modes and their energy content.

References: Lumley, J.L. (1967). The structure of inhomogeneous turbulent flows. In Atmospheric Turbulence and Radio Wave Propagation, 166–178. Holmes, P., Lumley, J.L. & Berkooz, G. (1996). Turbulence, Coherent Structures, Dynamical Systems and Symmetry. Cambridge University Press. Sirovich, L. (1987). Turbulence and the dynamics of coherent structures. Quarterly of Applied Mathematics, 45(3), 561–590.

Computing POD

Energy Spectrum tab

Use the energy spectrum to decide how many modes to use for reconstruction and interpretation. A steep drop after Mode 1 or 2 indicates a flow dominated by one or two strong coherent structures. A slow gradual decay indicates broadband turbulence with energy distributed across many scales.

POD Energy Spectrum tab. Bars show the energy percentage per mode; the orange curve shows cumulative energy. Dashed horizontal lines mark the 50%, 80%, and 90% thresholds. The readout strip at the bottom shows how many modes are needed to reach each threshold.

Figure 1:POD Energy Spectrum tab. Bars show the energy percentage per mode; the orange curve shows cumulative energy. Dashed horizontal lines mark the 50%, 80%, and 90% thresholds. The readout strip at the bottom shows how many modes are needed to reach each threshold.

Spatial Modes tab

Use the ‘Mode‘ spinbox or ‘<< Prev‘ / ‘Next >>‘ buttons to step through modes. Use the ‘Component‘ dropdown to inspect different velocity directions. The title shows the mode number and its energy fraction.

POD Spatial Modes tab showing Mode 1 of the U component. Red and blue regions represent opposite-signed velocity fluctuations associated with the dominant coherent structure in the flow. The energy fraction of the mode is shown in the plot title.

Figure 2:POD Spatial Modes tab showing Mode 1 of the UU component. Red and blue regions represent opposite-signed velocity fluctuations associated with the dominant coherent structure in the flow. The energy fraction of the mode is shown in the plot title.

Temporal Coefficients tab (TR only)

Shows the temporal coefficient time series an(t)a_n(t) for the selected mode and its power spectral density. A sharp peak in the PSD indicates a periodic structure at that frequency (e.g. vortex shedding or shear layer flapping).

Reconstruction tab

POD Reconstruction tab. Left: original snapshot. Center: low-order reconstruction with selected modes. Right: residual (original minus reconstructed). The RMS reconstruction error is shown at the bottom.

Figure 3:POD Reconstruction tab. Left: original snapshot. Center: low-order reconstruction with selected modes. Right: residual (original minus reconstructed). The RMS reconstruction error is shown at the bottom.

The three panels show the original field, the low-order reconstruction, and the residual. A residual below 10–20% RMS generally means the selected modes capture the dominant structure.

Exporting

Click ‘Export Modes…‘ to save all spatial modes as a Tecplot .dat file and temporal coefficients as a .csv file.